• 
  2024-07-10

  How to Increase the Output of Dry Mortar Production Line?

  As we all know, the output of dry mortar production line is mainly determined by the configuration of equipment, but the facts are different. General small dry mortar production line, did not achieve automated production, the use of manual feeding, etc., production capacity generally has no room to increase. Therefore, the increased capacity of dry mortar production line here is mainly for tower complete sets of equipment and automatic production lines. Generally, in the dry mortar production line, the entire production process is controlled by an automated control system, so to further increase production capacity can be started from several aspects: 1. Strictly control the working time of workers, mainly for the workers operating the dry mortar production line. Make good use of every minute to ensure production efficiency. There is a common problem in the dry mortar industry, that is, the dry mortar production line is still running, and there are many operators. This will make the overall production efficiency is reduced. 2. Increase the control of all links, such as raw material reserve, feeding, and packaging of finished products, strictly control all links, so as not to miss anything. 3. Replace the old dry mortar production line, with...

• 
  2024-07-05

  Which is more Advanced, Three Drum Dryer or Triple Cylinder Drying Machine?

  The two have similarities: 1. All industrial dryers are used to dry sand and other materials with good fluidity. 2. All are composed of three cylinders, and the material goes back and forth in the dryer three times to achieve full drying of the material. 3. Small floor area, high heat utilization rate, energy saving and environmental protection, dry thoroughly. The difference between the two: 1. Generally speaking, the three-return dryer is short in length and large in diameter, while the three-cylinder dryer is slightly longer in length and relatively small in diameter. 2. The three-cylinder dryer has no taper from the appearance, and is slightly longer, while the three-return dryer has a slight taper from the outside, and is thicker and shorter. 3. The three cylinders inside the three-return dryer have a certain taper, and the three cylinders inside the three-cylinder dryer have no taper. 4. Generally speaking, the length of the three-cylinder dryer can be designed to be longer, and the three-return dryer is designed to be shorter. Which of the two dries better? We suggest that it is better to use a three-cylinder dryer or multiple three-return dryers for drying materials above 50 tons per hour; The...

• 
  2024-07-05

  What factors should be considered when using Sand Dryer?

  1. Drying temperature: According to different materials, in the case of drying quality, try to choose a higher drying temperature to speed up the drying speed. 2. Humidity: Materials have different humidity. 3. Wind speed of hot air medium: The speed of hot air medium in the drying room is related to the drying speed, material shape and material characteristics. 4. Drying speed and drying method selection: drying should be controlled under technical parameters, such as temperature, humidity and wind speed, in order to achieve the retention of raw materials during the drying process. 5. Material placement: Stack thickness and placement method affect the drying speed. Reasonable control of pile thickness, increase heat exchange area and ventilation, speed up the drying speed. 6. Mixing and drying of different varieties: in principle, when raw materials are dried, a single variety is needed, and it is impossible to mix and dry together.

• 
  2024-07-04

  Precautions for installing Sand Tumble Dryer, do you need a Technician?

  Sand tumble dryer is a kind of equipment for drying sand, minerals and other wet raw materials, widely used in more industries. Installation of sand tumble dryer need to pay attention to matters: 1. Select an installation site. When choosing an installation site, you should consider whether there is enough space and ventilation around the equipment. The equipment installation area should be flat and trouble-free to facilitate future equipment maintenance and troubleshooting. 2. Check the installation environment. Before installing the sand tumble dryer, check the site environment and ground conditions to ensure that the equipment can be installed on the ground smoothly, so as to avoid shaking and loosening during the operation of the equipment. 3. Ground the power supply. Before installing the sand tumble dryer, it is necessary to check whether the power supply meets the electrical requirements of the equipment. In addition, a grounding device must be installed around the device to avoid hazards such as electric shock or electric fire. 4. Disassemble the device. Remove the equipment from the container and assemble it according to the marks and drawings. Note the orientation and dimensions of the mounting components to ensure that the device is assembled correctly. 5....

• 
  2024-07-03

  Is it difficult to distinguish between dry mixed mortar and wet mixed mortar? Teach you how to easily choose mortar – Part Two

  Sand is treated in different ways: The sand for wet mixed mortar does not need to be dried, while the sand for dry mixed mortar needs to be dried. Transport equipment is different: Wet mixed mortar, the transportation radius is within 40 kilometers, and the transportation time is not more than one hour. Each ton of wet mortar contains 170-190 kilograms of water, which is 15% more than the transport volume of dry mixed mortar, and the electricity consumption required for the production of this part and the fuel consumption of transportation will increase a certain cost. Wet mixed mortar is usually transported centrally by mixing tank trucks to ensure that the mortar does not produce stratification and segregation during transportation. At present, the usual tank car volume of concrete enterprises is 9 square, and it is necessary to have a large construction surface and construction personnel at the same time to consume the wet mixed mortar transported every day, and the supply method of “small number of times” is the reason for the high transportation cost of wet mixed mortar. Transport mode of wet mixed mortar: dry mixed mortar, transport radius can radiate to 80 kilometers, bulk dry mixed...

• 
  2024-07-03

  Is it difficult to distinguish between dry mixed mortar and wet mixed mortar? Teach you how to easily choose mortar

  Ready-mixed mortar refers to a variety of mortar mixes produced by specialized manufacturers and used in construction projects. It is a new building material developed in recent years in China. According to different production methods, ready-mixed mortar can be divided into dry mixed mortar and wet mixed mortar two categories. So what are the differences between dry mixed mortar and wet mixed mortar? Dry mixed mortar: Dry mixed mortar is a dry mixture that evenly mixes dry materials and is supplied in bulk or bag form. It needs to be used after adding water or supporting liquid at the construction site and stirring it evenly. The storage period of dry mixed mortar is longer, usually 3 months or 6 months. Wet mortar: Wet mixed mortar is a wet mixed mixture composed of all components including water, which can be used directly on the construction site, but it needs to be used before the mortar sets, and the long storage time is not more than 24 hours. The difference between dry mortar and wet mortar: Mortar status and storage time are different: Wet mixed mortar, the finished product storage time is short, the length is not more than 24h, must be...