• 
  2024-06-28

  What Kind of Sand Dryer is Commonly Used?

  What is commonly used is a three-cylinder dryer, the main features of the three-cylinder dryer: 1. High technical content, medium, inner cylinder self-insulation ability, high thermal energy utilization rate, low outlet temperature, greatly extend the service life of the dust collector. 2. Different lifting devices are used in different areas of the inner, middle and outer cylinder respectively, which can increase the lifting rate to about 40%, reduce the “wind tunnel”, increase the contact rate between boredom and hot air flow, and greatly increase the drying efficiency. 3. Synchronous drive with age support wheel, high rotation efficiency. 4. Small footprint, the use of the whole 100 bracket, easy installation, less failure rate, easy maintenance, basic investment. 5. The inlet and discharge device adopts structural soft seal, small air leakage rate, high thermal efficiency and low energy consumption. 6. The process flow can be downflow or counterflow. 7. Optimized structural design and heat-resistant treatment technology lay the foundation for long-term, trouble-free operation of the dryer. 8. According to the different nature of the material, the speed regulating motor or frequency converter is used to reasonably adjust the cylinder speed to increase the drying efficiency. 9. Using the principle of aerodynamics, the...

• 
  2024-06-27

  Quartz Sand Triple Cylinder Rotary Drying Machine

  An efficient and environmentally friendly Drying solution -Quartz Sand Triple Cylinder Rotary Drying Machine: Quartz sand is a natural mineral widely used in glass, ceramics, coatings and other industries. Because of its high light transmittance, high temperature resistance, corrosion resistance and other characteristics, it plays an important role in many industrial fields. However, quartz sand needs to go through many processes in the processing process, of which drying is a crucial part. How it works: Quartz Sand Triple Cylinder Rotary Drying Machine adopts advanced heat energy recovery technology to import the heated hot air into the cylinder, so that the quartz sand rolls in the cylinder and fully contacts the hot air. With the rotation of the drum, the quartz sand is constantly stirred and heated in the process of progress, so that the water gradually evaporates and is discharged by the exhaust port. At the same time, part of the exhaust gas is recovered through the thermal energy recovery system, which is used to heat fresh air, further improving the thermal efficiency. Features and advantages: High efficiency and energy saving Wide range of application High degree of automation Clean and environmental protection Application scenario: Glass industry Ceramic industry Coating...

• 
  2024-06-21

  The Main Components of Dry Mortar

  Dry mortar is a semi-finished mortar product that is accurately mixed and evenly mixed with the raw materials at the factory. At the construction site, it only needs to be mixed with water. Because there are many types of dry mortar, it is widely used. One of its biggest features is that it can play a role of adhesion, decoration, protection, and lining with a thin layer. For example, the mortar with the function of adhesion mainly includes masonry mortar, tile adhesive mortar, grout mortar, and anchoring mortar; the mortar with the function of decorative effect mainly includes various plastering mortar, interior and exterior wall putty, colored decorative mortar, etc.; the mortar with the function of protection includes waterproof mortar, various corrosion-resistant mortar, self-leveling floor mortar, wear-resistant mortar, thermal insulation and heat preservation mortar, sound-absorbing mortar, repair mortar, mold-proof mortar, anti-mildew mortar, shielding mortar, etc. Therefore, its components are also relatively complex, which can be summarized as consisting of adhesive materials, fillers, mineral admixtures, pigments, and additives. 1. Adhesive materials. The commonly used adhesive materials for dry mortar are: Portland cement, ordinary Portland cement, high-alumina cement, calcium silicate cement, natural gypsum, lime, silica fume, and mixtures of these materials. Portland...

• 
  2024-06-04

  Tower Type Dry Powder Mortar Mixing Plant!

  Tower Type Dry Powder Mortar Mixing Plant! With a production process arranged from top to bottom, your production will run smoothly. Perfect for ordinary mortar and various special mortars, offering a wide variety of products with minimal cross-contamination of raw materials. Features: a small footprint, sleek design, low energy consumption, multiple packaging methods coexisting, but a relatively large initial investment. Ready to revolutionize your production process? #TowerTypeMixingPlant #EfficientProduction #InnovativeTechnology

• 
  2024-05-20

  Purchase model of Sri Lankar customer: TDS6215 sand dryer & TDSJ2 dry mortar plant

  Purchase model of Sri Lankar customer:TDSJ2 dry mortar plant, tds6215 sand dryer Sri Lanka customer configured TDS6215 sand dryer and tdsj2 dry mortar production line, the customer preferred to dry the sand, sieve 2 kinds of specifications into different silos for storage, and then with the pneumatic conveying storage of cement, through the screw conveyor into the dosage system, and then into the mixing system, and ultimately for the valve pockets encapsulated palletizing.

• 
  2024-05-04

  3 sets of dry mortar mixed plants, featuring 1 plough share mixer and 2 twin shaft paddle non-gravity mixers.

  3 sets of dry mortar mixed plants, featuring 1 plough share mixer and 2 twin shaft paddle non-gravity mixers. To share the same heart and morality, to win together. Don’t miss out! Contact us today for more details.